本产品主要用于各种金属、玻璃、真空电镀、水电镀、电泳、阳极氧化铝、电解板、铝塑板、喷塑、喷粉、静电喷漆面、烤漆面以及各种天花吊顶氧化板、镜面板、覆膜板、辊涂板等制品的丝印及移印。 2、产品特性：亮光、附着力佳、快干、耐冲压。 3、稀释剂：用我司B-03专用稀释剂或783开油，用718洗网水清洗网版。 4、固化剂：单组份使用，也可选择添加我司JS-10专用固化剂用于增加油墨附着力及物理化学抗性。 5、油墨调配方法：开罐先搅拌均匀，取所需量油墨稀释到合适印刷粘度。如需添加固化剂，先加固化剂搅拌后静置10分钟，待油墨与固化剂完全交联后再进行稀释。 6、干燥时间：常温干燥，表干时间5-10分钟，实干时间在24小时以内，80℃烘烤20分钟可快速干燥。 7、添加固化剂后的使用时限：4-6小时，过期请弃用，剩余油墨不可回收。 【性能检测】 1、3M胶带划百格测试：100%无脱落 2、耐冲压测试：1mm厚铝板180°折弯无变化。 3、耐酒精测试：用脱脂棉沾浓度99%工业酒精以500G力水平来回200次无脱色。 【注意事项】 1、先小量试印确认符合要求后再批量生产。 2、做好承印物的表面清除油脂及杂质工作，以促进附着效果。 3、附着力、硬度、耐酸性、耐酒精性、耐化学品性、抗划伤性、耐磨性等性能的检测， 需要完全固化后方可检测。 4、未经允许情况下，不得将本系列油墨与其它类型油墨混用及配色。 5、油墨，稀释剂使用及储存时严禁烟火。 6、使用时注意施工场所的通风状况良好，尽量避免皮肤直接接触。 7、本品不慎溅入口、鼻、眼、耳内，应用大量水清洗或直接求助医生。 This product is mainly used for metal, glass, water, vacuum plating, electroplating, electrophoresis, anodized aluminum, electrolytic plate, aluminum plate, electrostatic spray, spray, spray paint, paint oxidation of surfaces as well as a variety of ceiling panels, mirror plate, coated sheet, roll-coated sheet products, such as screen printing and pad printing. 2, product features: light resistance, good adhesion, quick-drying, stamping. 3, thinner: with our B-03 special thinner or 783 oil, clean screen with 718 wash water network. 4, curing agent: single-component, or you can choose to add our JS-10 special curing agent used to increase ink adhesion and chemical resistance. 5, ink method: opening mix, obtaining the necessary amount of diluted ink to a suitable viscosity of printing. If you need to add curing agent, reinforcing agent first stir and let stand for 10 minutes until the ink completely cross-linked and then diluted with the curing agent. 6, drying time: dry at room temperature, surface drying time of 5-10 minutes, doing time in less than 24 hours, 80 deg c bake for 20 minutes can dry quickly. 7, after you have added curing agents use time: 4-6 hours, expired please discard used, surplus ink can not be recovered. "Testing" 1, 3M tape hundred tests: 100% no loss 2, punch resistance test: 1mm thick aluminum plate 180 ° bending was not changed. 3, resistance to alcohol testing: concentration 99% industrial alcohol with cotton wool dipped in 500G strength 200 times without bleaching. "Note" 1, a small print to confirm trial meets the requirements prior to mass production. 2, remove grease and impurities on the surface of the substrate, in order to promote adhesion effect. 3, adhesion, hardness, resistance to acid, alcohol, chemical resistance, scratch resistance, wear resistance, such as performance testing, needs to fully cure before making an inspection. 4, cases without permission, this series ink may not be mixed with other types of ink and color matching. 5, ink, thinner, use and storage of fireworks is prohibited. 6 be aware of construction, the use of the ventilation of the premises in good condition, try to avoid direct skin contact. Entrance 7, this product is accidentally spilled, nose, eye, ear, using large amounts of water to wash or to seek help directly from the doctor/
